ICP Alltek

  1. ICP Alltek
  2. Products
  3. Joint fillers
  4. Alltek Tekjoint Allégé

Alltek Tekjoint Allégé

Lightweight jointfiller plaster

DESCRIPTION

Alltek Tekjoint Lite is a ready-to-use, light grey plaster with exceptional ease of application and very little drying shrinkage.

USE

Alltek Tekjoint Lite is used for plastering joints between plasterboards with feathered edges and for smoothing.
Typical spreadability Approx. 0.3 l / m² of plasterboard wall, i.e. a yield of +/- 56 m² for a 17 l bucket, +/- 16m² for a 5 l bucket.
Recommended thicknesses
  • Min. thickness: 0,3 mm
  • Max. thickness: 3 mm
Packaging
  • 5 litre plastic bucket.
  • 17 litre plastic bucket.

Détails

TECHNICAL SPECIFICATIONS

Typical Spreadability

Approx. 0.3 l / m² of plasterboard wall, i.e. a yield of +/- 56 m² for a 17 l bucket, +/- 16m² for a 5 l bucket.

Density

1,1 +/- 0,1 kg/l

Solid Content

  • Solid content by mass: 61%
  • Solid content by volume: 53%

Application conditions

  • +5°C to +35°C
  • Max. relative humidity 70%

pH

8 +/- 1

Cleaning tools

With water

Drying

  • 24 h on average, depending on application thickness, temperature, ventilation, humidity and substrate type. Sanding and recoating: after complete drying.

Recommended thicknesses

  • Min. thickness: 0,3 mm
  • Max. thickness: 3 mm

CHARACTERISTICS

  • Ready to use
  • Easy to apply.
  • Ergonomic and rapid handling.
  • Outstanding adhesion.
  • Very good spreading power.
  • Excellent adhesion to jointing tape.
  • Easily sanded.
  • Fire rating: A2-s1, d0 as per European standard EN 13501-1.
  • Classification: group III class 2 as per AFNOR NF T 36-005, compliant with the standards AFNOR NF T 30-608 and EN NF 13963.
  • Certification CSTBat no. 203-06-821 associated with jointing paper Tape +

PACKAGING AND STORAGE

  • 5 litre plastic bucket.
  • 17 litre plastic bucket.
  • Shelf life is 9 months in unopened original packaging, protected from frost and extreme heat.

ENVIRONMENTAL INFORMATION

  • VOC content: < 2 g/l.
  • Indoor Air Emission Class

METHOD OF APPLICATION

Substrates:

  • Plasterboard.

Preparation of substrate:

  • The substrates, preparatory work and application conditions must be compliant with applicable building trade regulations (e.g. DTU) and standards.

Application tips:

  • Stir before use and add maximum of 0.8 l of water/17 l bucket, if necessary.
  • Plaster over any screw heads.
  • Manual or machine application with a high pressure pump, with nozzle sizes 531 to 535.
  • Manual application with Bazooka or supplied by high pressure pump (APLA-TECH system) possible.
  • Manually plaster the feathered plasterboard section with Alltek Tekjoint Lite, then press on the jointing tape with the same plaster. Fill the joint mechanically using a loaded Bazooka and press down the tape with a plastering knife.
  • After drying, skim once or twice manually or mechanically with the finishing attachments.
  • Sanding with grain size 100 to 150

Recommendations:

  • Applying Alltek Sprayplast equalizes differences in absorption between the paper covering of the plasterboard and the plaster. It reduces inequalities and visible surface variables when viewed at oblique angle.

HEALTH AND SAFETY

The safety information sheet is available from: www.icp-alltek.com/en-gb/documentation/